New Heat Pump Quoted but Your Panel Is Full?
Switching from a gas furnace to a heat pump is a smart move for hot summers and mild winters. But the HVAC quote often comes with a catch: your panel may not have room for the new circuit.
Many older homes here have panels with no open slots or 100 amp service that is already busy. Before you assume you need a big upgrade, we check what your home actually needs. Often a new circuit fits with some rearranging. Sometimes a panel upgrade makes sense, and we show you why.
A heat pump replacing a gas furnace may also qualify for SMUD rebates, and some panel upgrades tied to electrification qualify for Go Electric. We check what applies before quoting.
Homeowners and HVAC Contractors We Wire For
Gas to Heat Pump Switchers
Need a new 240 volt circuit and disconnect for a heat pump replacing a gas furnace.
Mini Split Buyers
Mini split electrical wiring for one or more indoor heads, each with its own outdoor unit or a shared one.
AC Replacements
New AC units sometimes need a different breaker size or a new disconnect.
HVAC Contractors
As an electrician for HVAC contractor partners, we handle the electrical side so your crew can set the unit and go.
Whether you hired the HVAC crew yourself or the contractor brought us in, we make sure the electrical side passes inspection the first time.
Everything We Wire for Your HVAC Install
Here is what a typical heat pump or AC circuit job includes:
- A dedicated 240 volt breaker sized to the unit’s nameplate
- Copper wire run from the panel to the outdoor unit
- A new outdoor disconnect within sight of the unit
- A new whip from the disconnect to the unit
- A heat pump water heater circuit install if you are switching that too
Mini splits often need a little extra planning, since each outdoor unit may serve one or more indoor heads. We follow the manufacturer’s wiring diagram and confirm breaker sizes with your HVAC installer before running wire.
Heat Pump and Mini Split Circuits Timed to Your HVAC Install
Nothing is worse than a new heat pump sitting on its pad with no power. We coordinate dates with your HVAC installer:
- Before the set: We run the circuit and disconnect so power is ready.
- Same day as the set: We make the final connection once the unit is in place.
- After the set: We book the county inspection and stay until it passes.
That teamwork is why HVAC electrical upgrade Sacramento County projects with us finish on schedule. Every job starts with our load check first approach.
For heat pump water heaters, we also check the location, since many sit in garages that may need a new 240 volt circuit run from the panel.
AC Disconnect, Whip and Breaker Upgrades
Outdoor AC parts take a beating from 100 degree summers and winter rain. AC whip and disconnect replacement fixes:
| Part | Common Problem |
|---|---|
| Disconnect | Rusted box or failed fuse holder |
| Whip | Cracked or sun damaged flexible conduit |
| Breaker | Wrong size for a new unit, or worn from years of trips |
An AC disconnect replacement 95660 job or AC breaker upgrade North Highlands owners book is often quick, and it can stop summer breaker trips.
Replacing a worn disconnect or whip during an AC service visit is often a quick job. If your HVAC tech flagged one of these parts, send us a photo and we can usually quote it on the phone.
Heat Pumps and Mini Splits We Powered Up
Recent jobs include mini split installation electrician Antelope work for a two head system, a heat pump circuit near Madison Avenue that replaced a gas furnace and a new disconnect for an AC swap in Larchmont Village.


On the Madison Avenue job, the homeowner was switching from a gas furnace to a heat pump. A load calculation showed the existing panel had room, so we ran the circuit and disconnect without an upgrade.
Breakers, Disconnects and Wire for HVAC Equipment
We install double pole breakers matched to your panel, fused and non fused disconnects, liquid tight whips, copper wire sized to the unit and line voltage connectors.
Every circuit is sized to the unit’s nameplate, not a guess. Using the right breaker protects the compressor and keeps your warranty intact.
HVAC Circuit Prices in North Highlands by Run Length
Your heat pump circuit cost depends on how far the unit sits from the panel and whether the panel needs work.
| Job | Typical Price Level |
|---|---|
| Disconnect and whip replacement | Lowest |
| New circuit, short run | Moderate |
| New circuit, long run | Higher |
| Heat pump panel upgrade North Highlands owners need | Adds $2,500 to $8,000 for panel and meter work |
Panel ranges from SacValley Contractors 2026.
Your heat pump wiring price comes in writing from your HVAC equipment specs and a panel photo.
If the panel needs work, we show you the load numbers and quote both paths, so you can decide with clear facts.
Coordinate Your Circuit With Your HVAC Installer
Send us your HVAC quote or equipment specs. We will price the circuit and work around your install date.
FAQs: Heat Pump and AC Wiring in North Highlands
What owners ask before calling about who wires mini splits near me.
A new circuit near the panel costs less than a long run or a job that needs a panel upgrade. We quote from your equipment specs and a panel photo.
Yes. We coordinate dates so the circuit and disconnect are ready when the HVAC crew sets the unit.
Sometimes. We run a load calculation first. Many homes fit a heat pump on existing service, while others need a 200 amp upgrade.
Areas We Serve

